甲烷和二氧化碳在煤焦上反应制备合成气实验研究

以煤与甲烷共转化制备合成气的研究为背景,通过考察固定床反应器上甲烷和二氧化碳分别在石英砂、煤灰和煤焦上的反应过程,证实了煤焦中的碳结构在共转化过程中对甲烷转化具有催化作用。同时考察了反应温度（1073K～1223K）、CH₄/CO₂比（0.33~3.00）和气固接触时间等工艺条件对甲烷转化率、气相产物中H₂/CO比的影响。结果表明,甲烷的转化率随着反应温度和气固接触时间的增加而增大,随CH₄/CO₂比的增加而减小。在考察范围内甲烷的转化率最高达到了86%。反应物中CH₄/CO₂比的改变可以起到调节产品气中H₂/CO比的作用,0.4~2.0调节。     

助剂CuO和La2O3对NiO/α-Al2O3甲烷催化部分氧化制合成气引发过程的影响

采用分步浸渍法制备了NiO/α-Al₂O₃、NiO-CuO/α-Al₂O₃和NiO-La₂O₃/α-Al₂O₃三种催化剂,运用程序升温表面反应（TPSR）技术考察了助剂CuO和La₂O₃对NiO/α-Al₂O₃甲烷催化部分氧化（CPOM）反应引发过程的影响。结果表明,无论是否经过预还原处理,NiO/α-Al₂O₃催化剂在CH₄/O₂混合气氛下进行程序升温表面反应（CH₄/O₂-TPSR）时,即使升高到910℃也不能引发CPOM反应。添加助剂CuO或La₂O₃后,NiO-CuO/α-Al₂O₃和NiO-La₂O₃/α-Al₂O₃催化剂在CH₄/O₂-TPSR过程中均可以引发CPOM反应。原因分别是CuO促进了CH₄对NiO的还原以及抑制了O₂对Ni0的再氧化,La₂O₃减小了Ni晶粒粒径和还原时扩散阻力促进NiO的还原。     

甲烷在清洁 Pd(111) 及氧改性的 Pd(111) 表面解离的密度泛函理论研究

 采用广义梯度近似 (GGA) 的密度泛函理论 (DFT) 并结合平板模型, 研究了 CH4 在清洁 Pd(111) 及 O 改性的 Pd(111) 表面发生 C朒 键断裂的反应历程. 优化了裂解过程中反应物、过渡态和产物的几何构型, 获得了反应路径上各物种的吸附能及反应的活化能. 结果表明, CH4 采用一个 H 原子指向表面的构型在 Pd(111) 表面的顶位吸附, CH3 的最稳定的吸附位置为顶位, OH, O 和 H 的最稳定吸附位置均为面心立方. CH4 在清洁 Pd(111) 表面裂解的活化能为 0.97 eV, 低于它在 O 原子改性 (O 没有参与反应) 的 Pd(111) 表面的活化能 1.42 eV, 说明表面氧原子抑制了 CH4 中 C朒 键的断裂. 当亚表面 O 原子和表面 O 原子 (O 参与反应) 共同存在时, C朒 键断裂的活化能为 0.72 eV, 低于只有表层氧存在时的活化能 (1.43 eV), 说明亚表面的 O 原子对 CH4 分子的活化具有促进作用. CH4 在 O 原子改性的 Pd(111) 表面裂解生成 CH3 和 H, 以及生成 CH3 和 OH 的反应活化能分别为 1.42 和 1.43 eV, 说明 CH4 在 O 原子改性的 Pd(111) 表面发生这两种反应的难易程度相当.     

Synthesis of dimethyl ether from methane mediated by HBr (Special column of methane transformation, Article)

Dimethyl ether (DME) was synthesized from methane through a two-step process, in which CH₃Br was prepared from the oxidative bromination reaction of methane in the presence of HBr and oxygen over a Rh-SiO₂ catalyst and then, in the second step, CH₃Br was hydrolyzed to DME over a silica supported metal chloride catalyst. 12 mol%ZnCl₂/SiO₂ catalyst was found to be the most active, but it deactivated because of Cl⁻ losing.     

CeZrYLaO对Fe基整体式稀薄甲烷催化燃烧性能的影响

采用共沉淀法制备了高性能低铈储氧材料Ce_0.35Zr_0.55Y_0.07La_0.03O_1.95(OSM,储氧材料)和胶溶法制备了耐高温、高比表面的La-Al₂O₃并以它们为载体,制备了一系列整体式铁基催化剂。考察了该系列催化剂对甲烷稀薄燃烧的催化性能,并用低温N₂吸附-脱附,储氧能力(oxygen storage capacity,OSC),XRD,XPS和H₂-TPR等测试手段对载体和催化剂进行了表征。活性测试结果表明所制得的整体式催化剂Fe/OSM+La-Al₂O₃可在50 000 h^-1的高空速条件下使含量为1%的甲烷在474 ℃起燃,565 ℃完全转化;低温氮吸附-脱附测试结果表明,所制得的Ce_0.35Zr_0.55Y_0.07La_0.03O_1.95经1 050 ℃焙烧5 h后的BET比表面积达33 m²·g^-1,孔容为0.14 mL·g^-1;La-Al₂O₃经1 050 ℃焙烧5 h后的BET比表面积达125 m²·g^-1,孔容为0.46 mL·g^-1,是优良的催化剂载体;OSC测试结果表明,加入储氧材料(oxygen storage material(OSM))能增加催化剂的储氧性能,有利于催化活性的提高;XRD测试结果表明,OSM以均一固溶体存在;XPS测试结果表明,Fe₂O₃与OSM载体之间的相互作用最强;H₂-TPR测试结果表明,加入OSM能增加催化剂的还原性能,从而提高了催化活性。     

Kinetic studies of the oxidative coupling of methane over the Mn/Na2WO4/SiO2 catalyst

Oxidative coupling of methane is a direct way to obtain C2 hydrocarbon,and Mn-Na-W/SiO2 catalyst is the most promising among all the catalysts.The 2%Mn/5%Na2WO4/SiO2 catalyst was prepared by the incipient wetness impregnation method.A 7-step heterogeneous reaction model of the oxidative coupling of methane to C2 hydrocarbons was conducted by co-feeding methane and oxygen at a total pressure of 1 bar over the catalyst.The kinetic measurements were carried out in a micro-catalytic fixed bed reactor.The kinetic data were obtained at the appropriate range of reaction conditions (4 kPa＜Po2 ＜20 kPa,20 kPa＜PCZH4 ＜80 kPa,800℃＜T＜900℃).The proposed reaction kinetic scheme consists of three primary and four consecutive reaction steps.The conversions of hydrocarbons and carbon oxides were evaluated by applying Langrnuir-Hinshelwood type rate equations.Power-law rate equation was applied only for the water-gas shift reaction.In addition,the effects of operating conditions on the reaction rate were studied.The proposed kinetic model can predict the conversion of methane and oxygen as well as the yield of C2 hydrocarbons and carbon oxides with an average accuracy of ±15%.     

氧载体的氧物种直接氧化甲烷制合成气

甲烷部分氧化制合成气由于合成气中n(H2)/n(CO)接近2,可直接用于甲醇合成或烃类F-T合成等后续工业过程而在国内外受到了广泛的关注。利用氧载体的氧物种在无气相氧下直接选择氧化甲烷制合成气是天然气化工利用的新方法,本文介绍了该方法的基本原理、概念工艺和对氧载体的性能要求,对应用于该方法的铈基复合氧化物的掺杂和助剂对选择氧化甲烷性能的影响、钙钛矿氧化物氧载体的氧缺陷、氧物种迁移、结构稳定性及其氧物种氧化甲烷的性能进行了阐述和分析,提出了控制氧载体表面状态是获得高合成气选择性的关键,并对该技术今后的研究重点进行了展望。     

Cations of halogenated methanes: adiabatic ionization energies, potential energy surfaces, and ion fragment appearance energies

The DFT-B3LYP and G3X model chemistry were used to predict the cation structures and energetics of fluorinated, chlorinated, and brominated methanes. Ion–complex structures between methylene cations and HX (X = F, Cl, Br) were found for all H-containing cations, and [CHF–FH]⁺, [CF₂–FH]⁺, [CCl₂–ClH]⁺, and [CCl₂–FH]⁺ structures are more stable than their normal tetravalent structures. Several cations should also be better described as ion–complex structures between methyl cations and halogen atoms, e.g., [CF₃–Br]⁺. Transition states connecting normal and ion–complex structures were also located, and potential energy diagrams were constructed for decomposition of methane cations and to predict the fragmentation pathways. The G3X energies were used to predict the adiabatic ionization energies (IE_as) and ion fragment appearance energies (AEs) from methanes. Many of the experimental AEs correspond to the energies of transition states instead of the thermodynamic dissociation limits. Electronic supplementary material  The online version of this article (doi:) contains supplementary material, which is available to authorized users.     

三(4-硝基苯基)甲烷衍生物的结构和振动光谱的理论研究（英文）

用密度泛函理论优化了三苯甲烷(1)和一系列三(4-硝基苯基)甲烷衍生物2,3和4的几何结构,并计算了其红外光谱和拉曼光谱;通过与实验光谱的对比,对实验光谱中的谱峰进行了指认,并从理论上纠正了部分对3和4红外光谱谱峰不合适的实验指认;同时预测了2,3和4的拉曼光谱.结果表明,几种化合物的振动光谱计算结果与相应的实验结果吻合良好;且化合物2,3和4的拉曼光谱具有相似性.